Questions and plumbing advice in the DIY Plumbing Forum - .
Some popular plumbing forums: Plumbing Advice - Plumbing Tools - Plumbing Courses & NVQ's
Water Heater Screaming Sound on Cold Water Line Spring Check Valve
Have this water heater for around 1 year, and it started doing this some time ago.
Any suggestions on how to fix this?
Hi bit of a weird issue, I installed a grohe bathroom tap successfully 2 months ago bought from screwfix.
Last week the right hand hot tap makes a squeak noise as I turn it on or off, left tap is 100% perfect and noiseless.
This grohe tap is like one unit, so no screw notch or way I can remove...
Hi all, this is probably a daft question but I need to run my cold feed from one side of my wall mounted boiler to the other. Running it beneath the boiler is difficult with lots of obstacles, is it okay if I run soldered copper over / across the top of the boiler? It'll be about 4" off the top...
Hi guys....we have an old Astracast sink top....I think its a composite sink....has a big single bowl.
My wife thinks it looks scruffy....looks ok to me.....sound but the bowl has seen a lot of work.
So she wants a new one...Astracast it seems are no more.
The problem is its size.....looked...
Hi all,
I'm installing a concrete patio out back. By the wall under the kitchen sink I have an existing P-Trap gully for the grey water from the sink, dishwasher, washing machine etc.
When I pour the concrete there won't be any chance to dig it up anymore. From my own research I get the...
- Question
is it feasible to connect a flo force or saniflo shower pump drain to a washing machine standpipe
Hi all I'm hoping someone can shine a light on this for me
Since our stop tap on the pavement has now been filled with sand for whatever reason, we are relying on our property fitted stopcock (this is outside on our garage wall)
Unfortunately turning this to the closed position only reduces...
I'm working on a Quooker Flex tap with an unreliable tap-and-twist steam control. I think its the little PCB in the tap head. I've got a replacement but I'm unsure of the process for removing and replacing the PCB. It is sandwiched between the brass core of the tap and the stainless case. It...
I want to reconnect some outbuildings to an existing water supply. The supply pipe is old 22mm MDPE and buried for a fair distance so not going to dig it up and replace it 😬. Question is can I use normal 22mm plumbing push-fit connectors to make the connection as finding 22mm MDPE fittings...
I have a plumber coming tomorrow to change a cartridge on a badly dripping tap on my bathroom mixer unit. There is no separate isolating valve for this tap so I'll have to close the stopcock. I tried closing it today but it won't go absolutely 100% closed and there is still a very slight flow...
Hi All
I have a leak coming from within my Mira Elite QT shower. It seems to be flowing from behind the switching Control. Any ideas what could be causing this leak. Already Changed the Pump Elbow as one of the clips had popped which was causing a second small leak, Any idea? Is it time to buy...
Hi, basic question, any insight much appreciated.
Looking to have an outdoor tap in my front porch fed from 15mm pex coming up from suspended floor. Pic 1 is inside porch, pex temporarily clipped to give an idea of pipe placement (ignore shoddy blockwork of booted cowboy builder!), Pic 2 is...
Hi, after using bottom 2 to refill system.
Should the 2 circled be left facing upwards
Thanks
Hi guys
Bit of frustrating situation, I was preparing to solder a 15mm Tee by lining it up to get the positioning right, etc and it was quite tight feeding into one of the pipes. When I came to dismantle to apply flux, etc, this side has become completely stuck! I can't seem to remove it...
I have discovered a very old end feed 22mm t connector under the bath is very gently weeping water. It’s in a place and with pipework that are going to make it a pig to get at and replace as it is nested between other pipes. If I drain the system would it work to heat it up and end feed some...
Hi All, I want to remove the Brizo Faucet Handle ModelHL5332 to change the valve pine. There is a small leak. The handle has no screw. I wonder how to remove it so I can change the valve pine inside the handle. I don't want to put too much force and damage the handle. Can anyone give me...
- Question
My toilet flushes ok when the long flush button is pressed - but water continues to flow into the toilet bowl. No problems with the short flush. I have a Siamp Optima 50, the overflow funnel doesn’t seem to drop back down on the long flush. The short flush does all purposes but family members...
Not exactly a plumbing problem but here goes. I have known for a couple of years there was a water leak somewhere between the water meter, on our property, and the property itself. The water company fitted a new (smart) meter about 4 weeks ago. Now they have contacted us saying we have a leak...
I have attached an image of a kitchen tap which requires the housing around the cartridge to be removed. The housing is much more than hand-tight and I was wondering if plumbers have experienced this type of tap and how the housing is removed without damaging it.
Thanks.
Hello! We have a wobbly toilet seat… it’s a back to wall toilet and whilst one fixing is secure the other is not, and it looks like the fitter didn’t really attach it all. How do I go about fixing this please! The seat in question is from Qualitex.
Creating content since 2001. Untold Media.
Tags
Newest Plumbing Threads
-
-
Running copper pipework above / across a Gas boiler?
- Started by kristeva
- Replies: 2
-
Installing pipework to avoid airlocks
- Started by Matt0029
- Replies: 1
-
DUK Pipes for thermostat shower fitted at different heights
- Started by Delforkids
- Replies: 2
-
-
-
SPorcelanosa KRION Attica screen 1.2m, anyone?
- Started by Sebastian T
- Replies: 0
-
Cistern filling one third of the way
- Started by dwaindigital
- Replies: 4
-
Boiler losing pressure only on central heating- Started by SnosRap75
- Replies: 6
-
tanking. Is it ok to just seal everything with plastic.
- Started by Staggersandfalls
- Replies: 3
-
Pop quiz, does anyone recognise this radiator valve?
- Started by dimuc
- Replies: 4
-
SUsing coil to clear pipe leading to gutter
- Started by Sonya K
- Replies: 2
-
Replacing outdoor P-Trap Gully with Bottle Gully
- Started by DIwhYdidIstartThis
- Replies: 0
-
-