You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
feeds
"The Hand That Feeds" is a song by American industrial rock band Nine Inch Nails, released as the lead single from their fourth studio album, With Teeth (2005). It is the highest-charting song by Nine Inch Nails on all charts except for U.S. Modern Rock Tracks, where it stayed at number one for five weeks, because the single that followed, "Only", stayed at number one for two more weeks (non-consecutively), and the Billboard Hot 100 peaking at number 31, bested only by the group's 1999 single "The Day the World Went Away". It is, to date, Nine Inch Nails' only single to reach the top 10 of the UK Singles Chart, as well as their highest-charting single on the U.S. Mainstream Rock Tracks chart, peaking at number two. It was also a crossover hit, crossing over to pop radio as their first top 40 radio hit since "Closer" and "Hurt" in 1994 and 1995, respectively, peaking at number 31 on the Billboard Hot 100 chart.
Hi, I am reinstating an indirect hot water tank and have 2 cold water feeds coming into it from the same supply. One of the feeds has a float valve but what ever was on the other has been removed. Why would there be 2 feeds to the top of the tank? Can I blank one off and just use the float valve...
I've searched the forums for an hour - not found anything specific on this question.
Question 1- can we remove the UFH Mixer - and just set the Boiler Flow to 45deg?
Background (and see diagram)
I'm Helping our village hall, 14 year old UFH heating - the gas boiler just packed up -...
Afternoon ladies and Gents,
got a query I’m hoping some of you can help me with.
Mate and work colleague is doing some work at a house renovating areas of it. I’m doing some standard bits and bibs there but he has asked me about something I’m actually unsure of.
it’s regarding an AGA with...
I would appreciate some advice. I have a flat on the 3rd floor of a converted house, which has a lightwell in the middle of the flat. The bottom of the lightwell reaches the 3rd floor (my flat’s floor level) and has a roof lantern for the flat on the 2nd floor. I plan to build a small bathroom...
Hello again. I'm moving forward with my new-build project on, I need to plumb my 3 wet rooms up stairs, a downstairs loo and kitchen/utility.
Due to lack of availability of a decent local plumber I'm doing the work myself.
I wanted to use manifolds for hot and cold supplies. 22mm to feed the...
House is in 4 x sections. 4 x Thermostats. I not starting the boiler. Have switch out the broken section to another section and it starts that other good section. Have put good pair on bad section, no start. Have pulled out the mass of wiring and checked all connections are good. They are. Have...
My kitchen sink and dishwasher are connected on the end of the hot/cold feeds from bathroom above it.
The pipes run down a corner of the kitchen wall and I'm thinking of having it rerouted. We are having a new kitchen so the opportunity presents itself to fairly easily reroute so the...
Hi,
I am having some issues with my radiator heat up times on two of my radiators and I am assuming that it is a flow rate issue or something along those lines.
I have a 4 bed (large) old semi-detached house.
11 Radiators
Worcester 36CDi Compact Combi-Boiler
All my rads end up being supplied...
The attached picture shows a 2.1m wall which will have a D/W on the left, an 90cm sink unit in the middle and a bin unit on the right.
Unfortunately, as you can see, the plumber has forgotten to create any soft water feeds to the dish washer and we also requested both Hard and soft feeds for...
Hi all,
I've been asked to modify the water supply to a hotel.
The front of the old hotel is connected to the water mains in front of the hotel, and the rear extension backs onto a different street and has an other water main serving the back only.
So can I simply connect the pipework inside...
Hello all
Sorry, another post where i am trying to order the correct taps from Germany for use here in Ireland. I have already been told that I can get a reducer to allow adapt to the different pipe diameters. 3/8" in Germany, to 1/2" here in Ireland (which I think is actually slightly...
I just bought several vertical column hudson reed rads to install in new hot water heating system. I notice that when I screw the vales to the two lower rad ports that I can look straight thru to the other port. I expected there to be a baffle of sorts directing hot water up thru the crumbs and...
Naphelge
Thread
column
feeds
installed
ports
return
valves
vertical
water
Good evening all,
To outline the scene, we have fitted a new bathroom( bath & basin) on the 3rd floor of a house and ran the plumbing across the landing to the loft of the two storey extension, where the tanks are located above the hot water cylinder. However obviously the water flow will be...
One of which has a gate valve on which turned off the hot but the first I tried (gate valve appeared functional, not spinning) didn't.
Not seen before. Didn't have time to investigate further, was just checking hot could be turned off for a tap change quote.
Guys, need some advice
if I have s high pressure water system which runs at 20 bar which feeds a unit and a air line running at 6 bar also feeds a unit and for some reason a non return valve fails allowing the air water to mix in the water line, would this make the system still sit a 20 bar or...
Morning,
I have two questions....
I presume that taking a toilet cistern feed of the balanced cold is fine and itdoesn’t need to be run back and connected before the PRV?
On a kitchen sink we have a mixer - Can we run a cold feed pre the softener, andfit 1 2bar PRV so that it matched the...
Hi,
The kitchen/diner is going to be fitted with UFH. It will be a block and beam floor with a small later of sharp sand to level, 100mm insulation and then a 55mm anhandryte screed. Should the water feeds to the kitchen be pipe in pipe on the block/beam under/in the bottom of the insulation or...
When we were changing our carpets it was clear there was a problem with the shower as the boards were wet, which we traced to being a leak with the connections at the back - it's an aqualisa aquastream powershower which has internal pushfit fittings.
So, hot and cold feeds turned off, I...
Just a general question. It seems to be well known that for certain reasons, cold feeds on o/v systems collect magnetic debris. Do combined F and Vs get the same problem?
Hi all,
I have a radiator by my front door which has a leak (now isolated to stop the leak) from a cental heating bleed valve - I suspect the cleaner hit it with a hoover and damaged it - but in order to replace it, I need to know what it is called so I can order the right part.
I am not...
jaffab
Thread
bleed
central
central heating
feeds
heating
radiator
thing
valve
whats
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.